EGW Holosun K Series Mount for Glock (fits Vortex Defender Series, Shield RMSC/RMS/SMS, Leupold DeltaPoint Pro)
This mount fits the:
- Glock 17
- Glock 17L
- Glock 19
- Glock 19x
- Glock 20
- Glock 21
- Glock 22
- Glock 23
- Glock 24
- Glock 26
- Glock 27
- Glock 29
- Glock 30
- Glock 30 SF
- Glock 31
- Glock 32
- Glock 33
- Glock 34
- Glock 35
- Glock 36 (Our mount is wider than the slide, but it will still work)
- Glock 37
- Glock 38
- Glock 39
- Glock 41
- Glock 42 (Our mount is wider than the slide, but it will still work)
- Glock 43 (Our mount is wider than the slide, but it will still work)
- Glock 43x (Our mount is wider than the slide, but it will still work)
- Glock 44
- Glock 45
- Glock 46
- Glock 48 (Our mount is wider than the slide, but it will still work)
- Canik TP9 SF
- Canik TP9 SA
- Bersa BP9CC
- Tactical Solutions .22lr Conversion
- Taurus G3c
- Taurus GX4 (non optic ready slide)
- Advantage Arms .22lr Conversion
- PSA Dagger (NON-optics ready)
Does not fit ANY/ALL Glock MOS models.
Does not fit ANY/ALL Glock slides that are already cut for optics.
WILL NOT WORK WITH ANY CANIK THAT HAS A STEPPED REAR SIGHT CUT
This mount will also fit the NON-optics ready PSA DAGGER
Material: 7075 Aluminum
Coating: Matte Black Hardcoat
Overall Length: 1.604"
Overall Width: .99"
Mounting Hardware: (2) 6-32 Button Head Screws, (1) 6-32 X 3/16 Set Screw
Red Dot Fitment:
Bushnell RXS-100
Crimson Trace CTS-1500
Holosun 407k
Holosun 407k -GR
.Holosun 507k
Holosun 507k GR
Holosun EPS-GR*
Holosun EPS-RD*
Holosun EPS-Carry-GR*
Holosun EPS-Carry-RD*
Jpoint
Leupold Delta Point Pro
Optima
Redfield Accelerator
Shield RMS
Shield RMSc
Shield SMS
Sig Romeo Zero
Swamp Fox Sentinel I,II
Our Glock sights are meant to be installed from the left to the right. The dovetail has a progressive taper to allow for easier install.
Simply remove the rear sight on your gun and replace it with our mount in order to mount your Leupold DeltaPoint Pro, JPoint, Redfield Accelerator, or Optima red-dot sight. You can take our mount off and replace your rear sight at any time. Mounting hardware included.
Installation Instructions
- Remove the rear sight*
- Install the EGW Sight Mount in the dovetail
- Tighten set screw (if applicable)
- Place the red dot sight on the EGW Sight Mount
(placing a small piece of paper between the red dot sight and the sight mount will make for easier removal and will keep Loctite off of the red dot sight.)
- Apply blue Loctite to the provided mounting screws
- Torque mounting screws to 15in/lbs
WE RECOMMEND THIS PLATE BE INSTALLED BY A QUALIFIED AND COMPETENT GUNSMITH.
Modification of your firearm may nullify the manufacturer's warranty.
This product should be installed and checked by a qualified gunsmith.
No liability is expressed or implied for damage or injury which may result from improper installation or use of this product.
